Stamp 4 Fun With Diana: Creative Card-iology Team May 2023 Returning Favorite Colors Blog Hop

Welcome to the Creative Card-iology Monthly Blog Hop

This month's theme is to make a card or project using

any of the 7 Returning colors listed below

BERRY BURST

BLUEBERRY BUSHEL

FRESH FREESIA

LEMON LIME TWIST

LOST LAGOON

MISTY MOONLIGHT

PRETTY PEACOCK

I chose to use Pretty Peacock and Berry Burst

as I love these two colors.

The stamp set I used for this card

is from the new 2023-2024 Annual Catalog

CRAFTING WITH YOU

and comes bundled with matching dies.

HERE ARE THE SUPPLIES USED TO MAKE THIS CARD

Crafting With You Stamp Set #161219
Crafting With You Dies #161225 or bundle together and save 10%
Crafting With You Bundle #161226
Berry Burst Stampin' Pad #147143
Pretty Peacock Stampin' Pad #150083
Berry Burst Cardstock (CS) #144243
Pretty Peacock CS #150880
Basic White CS #159276
Basic Black CS #121045
Vellum CS #101856
Silver Foil Specialty Paper #156457
Stampin' Cut and Emboss Machine #149653
Painted Texture 3D Embossing Folder #154317
Pretty Flowers Embossing Folder #155428 (Retired) or Substitute any Folder
Silicone Craft Mat #127853
Paper Snips #103579
Bone Folder #102300
Stampin' Dimensionals #104430 Mini's #144108
Berry Burst ⅜” Metallic-Edge Ribbon#145489 (Retired)
Substitute White Ribbon colored with Berry Burst Marker
Stampin' Seal Adhesive #152813
Fine Tip Glue Pen #138309
Take Your Pick Tool #144107
Paper Trimmer #152392

HERE ARE THE INSTRUCTIONS I USED TO MAKE THIS PROJECT

In this tutorial the name Seal refers to the use of the Stampin' Seal Adhesive.

Cut a piece of Pretty Peacock CS 8½" x 5½" (Score at 4¼"), then fold in have and burnish to form Card Base.
Cut a piece of Basic White 5¼" x 4". Stamp the greeting with Pretty Peacock Ink in the upper right side, then insert in Painted Texture 3D Embossing Folder and run thru the Stampin' Cut & Emboss machine.
Cut a piece of Basic White 2½" x 1¾”. Using Memento Black Ink, stamp the Big Shot stamp, then using the matching die run it thru the Stampin' Cut and Emboss machine.
Cut a piece of Basic Black 2½" x 1¾”, then using the paper trimmer die, run it thru the Stampin' Cut & Emboss machine.
Cut a piece of Berry Burst 1" x 1⅜”, then add adhesive and place it in the paper trimmer die piece.
Cut a piece of Vellum 2½" x 2½" and fold in half corner to corner to form a triangle.
Cut a piece of Berry Burst 3½" x 1¼"add adhesive to the back of the CS, then place inside the folded Vellum.
To make the mini embossing folder for the big shot die piece, run the vellum and Berry Burst piece thru the Stampin' Cut and Emboss machine, then cut as follows:
Place the embossed piece with the fold at the bottom. This will make 4 embossed pieces for the big shot piece. Cut off the Berry Burst piece on the left side and that side will now be put in your paper trimmer and cut four ½" strips which become your mini embossing folders.
Take a blade and cut your mini big shot die piece on the black line where the plates goes thru and down the left side to the bottom on the base plate.
Line up the mini embossing folder over the big shot die cut. Add adhesive to the bottom of the mini folder and trim if necessary. Slide thru the cut line and adhere in place on the platform.
Cut a piece of Basic Black and Silver Foil 2½" x 1". Using the Scissor die, run each of these thru the Stampin' Cut and Emboss machine. Save the tiny silver circle.
On the black piece, cut the handle pieces at the embossed mark.
Using the Fine Tip Glue Pen adhere the black handles over the Silver Foil. Now place the tiny silver circle in the black piece. Add a little adhesive where the scissors come together and open them slightly.
Place everything on the card to determine where to place the ribbon.
Add adhesive to both ends of the ribbon and adhere each end to the back of the card. Add dimensionals to the back of each of the die cuts. Make the scissors look like they are going to cut the card.
Add adhesive to the back of the white card front and adhere to the card base.
Add dimensionals to the trimmer piece, big shot and scissors and adhere to the card.
To put the final touches on the card, add a white matte dot for the embosser and a black matte dot for the blade on your trimmer die.